China High Quality Hydraulic Hose Connector Factories – Hydraulic Fluid Power Connection Winner 37° Flared Connectors/Adapters – Winner Fluid
China High Quality Hydraulic Hose Connector Factories – Hydraulic Fluid Power Connection Winner 37° Flared Connectors/Adapters – Winner Fluid Detail:
Product Introduction
Winner brand 37°flared connectors / adapters meet and exceed ISO 8434-2 metallic tube connections for fluid power and general use – Part 2: 37° flared connectors requirements and performance. The pressure ratings are higher than ISO 8434-2.
37° flared connectors are suitable for use with ferrous and non-ferrous tubes with outside diameters from 6 mm to 50.8 mm inclusive. These connectors provide full flow connections with metal-to-metal sealing in hydraulic systems operating to the working pressures shown in below table as tube sizes.
|
Tube outside diameter OD |
Wall thickness of tube for flaring |
Working pressure MPa |
||
|
Metric mm |
Inch in |
Metric tube mm |
Inch tube mm |
Carbon steel and stainless steel |
|
6 |
1/4 |
1.5 |
1.65 |
35 |
|
8 |
5/16 |
1.5 |
1.65 |
35 |
|
10 |
3/8 |
1.5 |
1.65 |
35 |
|
12 |
1/2 |
2 |
2.1 |
31 |
|
16 |
5/8 |
2.5 |
2.41 |
24 |
|
20 |
3/4 |
3 |
2.76 |
24 |
|
25 |
1 |
3 |
3.05 |
21 |
|
30 |
1 1/4 |
3 |
3.05 |
17 |
|
38 |
1 1/2 |
3 |
3.05 |
14 |
|
50 |
2 |
3.5 |
3.4 |
10.5 |
Both metric and inch tubing can be accommodated by changing the sleeve see catalogue sheet NB300 sleeve for inch tube and NB500 sleeve for metric tube. For new and future designs, the use of metric tubing is preferred.
They are intended for the connection of tubes and hose fittings to ports in accordance with ISO 6149-1, ISO 1179-1 and ISO 9974-1 and ISO 11926-1. And in new design in fluid power applications, stud ends in accordance with ISO 1179-3 and ISO 9974-2 and ISO 11926-3 shall not be used, the dimensions for the stud end shall conform to ISO 6149-3.
Below figure show the cross sections and components of a typical 37°flared connector.
Key
1 Straight stud connector body
2 Tube nut
3 Tube
4 Sleeve
5 O-ring
a Stud end in accordance with ISO 6149-3, ISO 1179-3, ISO 9974-2 or ISO 11926-3.
Below figure show the cross sections and components of a typical 37°male and female connector, the matched pressure see below table.
|
Size |
Thread |
Pressure rating |
|
1J-04 |
7/16″x20UNF |
58.6 |
|
1J-05 |
1/2″x20UNF |
58.6 |
|
1J-06 |
9/16″x18UNF |
48.3 |
|
1J-08 |
3/4″x16UNF |
41.4 |
|
1J-10 |
7/8″x14UNF |
37.9 |
|
1J-12 |
1.1/16″x12UN |
27.6 |
|
1J-16 |
1.5/16″x12UN |
24.1 |
|
1J-20 |
1.5/8″x12UN |
24.1 |
|
1J-24 |
1.7/8″x12UN |
14.5 |
|
1J-32 |
2.1/2″x12UN |
12.1 |
|
2J-04 |
7/16″x20UNF |
58.6 |
|
2J-05 |
1/2″x20UNF |
48.3 |
|
2J-06 |
9/16″x18UNF |
48.3 |
|
2J-08 |
3/4″x16UNF |
41.4 |
|
2J-10 |
7/8″x14UNF |
37.9 |
|
2J-12 |
1.1/16″x12UN |
27.6 |
|
2J-16 |
1.5/16″x12UN |
24.1 |
|
2J-20 |
1.5/8″x12UN |
24.1 |
|
2J-24 |
1.7/8″x12UN |
14.5 |
|
2J-32 |
2.1/2″x12UN |
12.1 |
Product detail pictures:
Related Product Guide:
Our well-equipped facilities and great good quality regulate throughout all stages of manufacturing enables us to guarantee total buyer gratification for China High Quality Hydraulic Hose Connector Factories – Hydraulic Fluid Power Connection Winner 37° Flared Connectors/Adapters – Winner Fluid , The product will supply to all over the world, such as: Estonia, Spain, Holland, Our solutions have national accreditation standards for experienced, premium quality goods, affordable value, was welcomed by people around the globe. Our products will continue to increase in the order and look forward to cooperation with you, Truly must any of people goods be of interest to you, make sure you letus know. We're likely to be delighted to give you a quotation up on receipt of one's in depth specs.
Product Number
Leave Your Message
By Liz from Swaziland - 2018.09.23 18:44
We are old friends, the company's product quality has been always very good and this time the price is also very cheap.
By Denise from Marseille - 2017.01.28 18:53